- Újdonságok
- Akciós termékek
- Robotépítés, Alkatrészek [446]
- Robots for the House & Recreation [1]
- Robot Toys and Hobbies [99]
- Professional & Service Robots [0]
- Robot - Books - Apps [5]
- STEM Education [115]
- LED & Lightening [2]
- Smart Devices & Gadgets & IoT [3]
- Wearable Technology [36]
- DIY Modules [1]
- Vendors & Brands [937]
- Adafruit [182]
- Arduino - Genuino [86]
- BBC micro:bit [3]
- BIOLOID [1]
- CodeBug [7]
- Cosmo [1]
- Elegoo [11]
- Elenco - Snap Circuites [19]
- FisherTechnik [6]
- Grove System [0]
- HEXBUG [15]
- Learning Resources [2]
- LEGO [1]
- LittleBits [66]
- Meccano [3]
- MakeBlock [10]
- Meet DIMM™ [1]
- Modern Robotics [0]
- Modular Robotics [2]
- OHBOT [4]
- OSMO [1]
- Ozobot [3]
- OWI [22]
- Pimoroni [0]
- Raspberry Pi [74]
- Sam Labs [1]
- SparkFun [0]
- Sphero [14]
- Thames & Kosmos [10]
- Tinkerbots [4]
- Tetrix Robotics [0]
- UBTECH [9]
- VEX Robotics [19]
- Wonder Workshop [3]
- WowWee [8]
- Málna-PC [347]

A2130 Adafruit Mono 2.5W Class D Audio Amplifier - PAM8302
This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps!
-
The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly.
Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Speaker is not included, use any 4 ohm or greater impedance speaker.- Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply
- 50dB PSRR at 1KHz
- Filterless design, with ferrite bead + capacitors on output.
- Fixed 24dB gain, onboard trim potentiometer for adjusting input volume.
- Thermal and short-circuit/over-current protection
- Low current draw: 4mA quiescent and 1uA in shutdown mode
Note: The terminal block included with your product may be blue or black.
-
Brand AdafruitTípus AudioÖsszeszerelést Igényel NemÁllapot ÚjCikkszám A2130